Hao4K影音

宅海网ContentsSpeaker SystemSKR-L500Getting StartedPackage Contents.Placement.海网海网海网Instruction ManualInstalling UsingUsing Cork Spacers with theSpeaker.2Wall Mounting.2Connecting the Speakers...............3Using Speaker Mounts/Brackets...3Thank you for purchasing an Onkyo speaker system.Please read this manual thoroughly before using yournew speakers.Following the instructions in thisAppendixmanual will enable you to obtain optimumOperating Precautions.3performance and listening enjoyment from yourspeaker system.SpeakerPlease retain this manual for future reference.Specifications宅嗨网Package ContentsWall MountingSKR-L500:Surround back speakerThe speaker can easily be wall mounted by using theSpeaker cable.9 m (brown)keyhole slots.To prevent the speaker from vibratingCork spacers,4 pcs.against the wall,attach four of the supplied cork spacersto the rear of the speaker.Placement■Mounting verticallySKR-L500To mount the speaker vertically,use the two keyholeslots shown to hang the speaker on two screws that areSKR-L500Cork spacerKeyhole slotforwall mountingSKR-L500:Surround back speakerThis speaker enhances the realism of surround soundand improve sound localization behind the listener.Mounting horizontallyPosition it behind the listener about 2-3 feet(60-To mount the speaker horizontally,use the two keyhole100 cm)above ear level.slots shown to hang the speaker on two screws that aresecurely screwed into the wall..The speaker cabinet is sensitive to extreme tempera-Keyhole slot for walltures and humidity,do not put it in locations subjectmountingto direct sunlight or in humid places.such as near anair conditioner.humidifier.bathroom,or kitchen..Do not put water or other liquids close tothe speaker.If liquid is spilled over the speaker,the drive unitsmay be damaged.As explained in this manual,mount the speaker on awall,or on the optional stands/brackets,otherwise,itCork spacersmay fall,causing personal injury or damage to thespeaker.The plaque of each speaker rotates so that you can posi-Using Cork Spacers with the Speakertion the speaker upside down.Caution:We recommend using the supplied cork spacers toA mounting screw's ability to support a speakerachieve the best possible sound from your speaker.Thedepends on how well it's anchored to the wall.If youcork spacers prevent the speaker from moving,provid-have hollow walls,screw each mounting screw into aing a more stable setup.stud.If there are no studs,or the walls are solid.usesuitable wall anchors.Cork spacersUse screws with a head diameter of 9.5 mmor less and ashank diameter of 4 mm or less.With hollow walls,usea cable/pipe detector to check for any power cables orwater pipes before making any holes.Bottom of theLeave a gap of 5 mmSKR-L500Wallbetween the wall and thebase of the screw head,asshown.(We recommend that youconsult a home installationprofessional.)Connecting the SpeakersUsing Speaker Mounts/BracketsRead the following before connecting your speakers:Threaded inserts for 5 mm machine screws are providedTurn off your amp before making any connectionson the rear and buttom of the speaker for wall-mountingThe nominal impedance of these speakers is 69.Usewith commercially available speaker mounts and brack-only an amp that supports this impedance.ets.Refer to the manual supplied with your mounts or.Pay close attention to speaker wiring polarity.Con-brackets for installation detailsnect positive (+terminals to only positive (+)termi-Note:nals,and negative (-)terminals to only negative (-The portion of the screw that goes into the speaker'sterminals.If the speakers are wired incorrectly,thethreaded insert should be between 5 mm and 9 mmsound will be out of phase and will sound unnaturallong.Be careful not to short theMount or bracketpositive and negative wires.Doing so may damage youramp.Connecting the Speaker CablesOperating Precautions1Strip the insulation from theThe speaker can handle the specified input power whenends of the speaker cables,used for normal music reproduction.If any of the fol-and twist the bare wires tightly.lowing signals are fed to them,even if the input poweris within the specified rating,excessive current may2Use the cables to connect speaker's inputflow in the speaker coils,causing burning or wire break-terminals to the corresponding speakerage:output terminals on your amp.1.Interstation noise from an untuned FM radio.To make a connection.while2.Sound from fast-forwarding a cassette tape.pressing the terminal lever,3.High-pitched sounds generatedby an oscillator,elec-insert the wire into the hole.andtronic musical instrument.and so on.then release the lever.Make sure that the terminals are5.Special test tones from audio test CDs and so on.gripping the bare wires,not the insulation.6.Thumps and clicks caused by connecting or discon-necting audiocables(Always turn off your amplifierbefore connecting or disconnecting cables.)7.Microphone feedback..The speaker contain strong magnets,so do not putmagnetic or iron objects such as screwdrivers close tothem.If you do,the object may be attached to theXXmagnets,causing personal injury or damage to thediaphragm.SKR-L500SKR-L500Surround backSKM-L500SSKM-L500SSKF-L500SKF-L500speaker(right)speaker (left)Surround rightSurround leftFront leftFront rightspeakerspeakerspeakerspeakerSKC-L500CCenter speaker⊕3